Compared with no additive condition, NO removal efficiencies with Na 2 CO 3, KCl and NaCl are increased by, and percentage points at 950 °C respectively, and Na 2 CO 3 additive even results in an increase of NO reduction by up to percentage points at 850 °C, which suggests that the catalytic ability of the three additives ...
Ignition temperature of coal and other dust is not affected by particle size. A big difference is made by the way coal dust comes in contact with a heat source. Thus, layered powder of coal can ignite at a much lower temperature (160°C approx.), whereas a cloud of coal dust will need 450650°C to ignite. Table shows some relevant data [5].
Densification and pyrolysis are two methods to upgrade biomass. To avoid ash fusion problems, NH4H2PO4 and Ca(H2PO4)2 were chosen as additives to mix with maize straw to produce biochar briquettes. Potassium transformation mechanisms between additives and biomass in pyrolysis were investigated by XRD, XRF, SEMEDS, and simulation. Results show that additives accelerate the production of ...
Cylindershaped fuel pellets that were 3 mm in diameter and 3 mm in height, with a mass of 20 mg, were produced by compressing dry coal processing waste under the pressure of 5 MPa. The first group of pellets from coal dust with a particle size less than 140 µm did not contain any additives. The pellets of the second group of fuel compositions contained an oilimpregnated porous polymer ...
interlayer compounds are introduced in the interplanar spacing of coke during the calcination process. The study of additives used to modify raw materials of the production process of developed mesophase and further needle coke production allows us to conclude that the most promising modifiers are organic compounds, namely polymers and ...
Purpose of Review This review presents an overview of highperformance ultrafiltration (UF) membranes, including fouling resistant, micellarenhanced, tight, adsorptive, and catalytic UF. The review discusses recent advances in the development of these membranes, focusing on their preparation method, performances, and applications. Then, the review concludes with a discussion of the challenges ...
Adding additive to the coal is an option and has grabbed the attention of many researchers for developing an additive. These additives for coal can effectively improve the combustion performance of the coal. This review paper contributes information about the impact of additives on coal combustion properties, coal calorific value, binder for ...
Researchers in Russia have improved coalburning efficiency with the use of catalytically active agents to intensify the combustion process. Copper salts were tested as activating additives to improve reactivity of highash coal fuels, such as anthracite, and semicoke. These fuels are characterized by high minimum ignition and combustion ...
The coal consists of raw combustibles and inert ash. Coal particle is assumed to be a sphere with a swelling core and modeled by the Lagrangian particle tracking (LPT) method [2], [22]. In simulations, the devolatilization process of raw combustibles releases the Volatile Matter (VM) into the gas while leaving the char in the core.
High VM content of coal is a reason for the accelerated temperature increase inside boiler. Slagging and fouling potential of the ashes of these 3 pattern coal are obtained with different indexes.
Catalytic coal gasification technology shows prominent advantages in enhancing coal gasification reactivity and is restrained by the cost of catalyst. Two typical biomass ash additions, corn stalk ash (CSA, high KNa and low Si) and poplar sawdust ash (PSA, high KCa and high Si), were employed to study the influence of biomass ash on pyrolysis process and char gasification reactivity of ...
To prepare the raw material for pelletization, some additives such as binder, limestone, coke/anthracite coal is used to form high grade iron pellets, which enhance the needed physical and chemical properties of pellet to process further. Binder plays the vital role to hold fines together and this can be agglomerated into pellet with high strength.
Aluminum silicatebased, aluminumbased, and magnesiumbased additives were used in coal combustion to comprehensively evaluate ash fusion temperature, thermal properties, ash deposit, emission, and ash mineral morphology. The results showed that additives in highrisk coal/blended coal could reduce ash sintering during the combustion.
The method of achieving more efficient use of engine fuels and increasing their octane number by means of organic fuel additives is widely known [].For example, methyltertbutyl ether (the amount of which produced in Russia alone is around 1 million t a year) is used as an additive to achieving more efficient use of diesel fuel, OFAs on the basis of alcohols and light ethers with ...
Denitrification experiments of cocombustion of coal and additives were carried out in a horizontal tube furnace. The results showed that calcium acetate limited the production of NO2. The optimum calcination temperature of CTABZrTiO2 was 673 K. The denitrification efficiency reached up to %, and desulfurization efficiency reached % when corncob, calcium acetate, and CTABZrTiO2 ...
Petroleum coke, which is a potential replacement for coking coals in the production of metallurgical coke, has received the name of a petroleum coking additive in Russia and the CIS countries.
When mixed with water, many drilling fluid additives are designed to function within a pH range of to 10. This allows the additives to become soluble and disperse and in effect, function. The pH can be adjusted to the proper level by adding specific additives to the water. Two of these additives include caustic soda and potassium hydroxide.
To help in building a recyclingoriented sustainable society, Nippon Steel Sumitomo Metal Corporation developed a waste plasticrecycling process using coke oven and put it into commercial operation in 2000. Now roughly 200,000 tons per year of waste plastics are processed in coke oven in Japan. In this process, the waste plastics collected from s are agglomerated to the sizes ...
The same high volatile bituminous coal carbonized by Chandra at 325°C at 6000 atm (not included in Fig. 16) showed an increase of bireflectance to Apart from the experiment at 850°C by Hryckowian and coworkers, in which bireflectance falls with rising pressure, there is a general trend of rising bireflectance with increasing pressure ...
Coal dust, or anthracite, is fast becoming a common additive in the green sand moulding process. It is a carbonaceous additive that under foundry conditions combusts and oxidises. Historically, the leading additive in green sand casting, as a carbonaceous material, was highly volatile bituminous coal, often referred to as sea coal.
© DZCrusher - كل الحقوق محفوظة
